|
|
 |
 |
|
WL-BRIDGE-OEM
Ethernet to WiFi Bridge & Access Point full module for OEMs
|
|
 |
 |
 |
The WL-BRIDGE-OEM enables to connect any industrial equipment with
an Ethernet 10/100 or TTL network interface, device is very compact and
is specially designed to satisfy the needs of the OEM and system integrator
markets.
The WL-BRIDGE-OEM device is also designed to work as a wireless bridge
between the wired MODBUS/TCP protocol and the radio network, this feature
allows to connect any MODBUS/TCP equipment to this network.
Thanks to its built-in WEB interface, the setup of the device is achieved
using the web browser installed on your computer (Internet Explorer, Netscape,
Mozilla ...).
WL-BRIDGE-OEM doesn't require any additional software to be installed
in your computer (no peripheral driver needed).
Product rely on the IEEE 802.11b standard (2.4 GHz) and is IEEE 802.11g
compatible, it features an Ethernet interface available on a RJ45 connector
or on a 4 pins HE10 connector for the TTL model.
The link is made safe by a WEP 64/128 bits encryption key, the nominal
range is 200 m (open space) for a 11 Mbps binary rate, emitter power is
+15dBm while receiver sensitivity is -84dBm.
Its size is extremely compact (L:76 x W:50 x H:18 mm) in order to be
integrated in any equipment equipped with an Ethernet port, consequently
opening to equipment access to the wireless world.
It can be connected the a printed circuit board through a female HE10
connector.
It can be powered from the DC power source (+3.3VDC or +5VDC), consumption
doesn't exceed 3W.
Click to this link to learn more about "Wireless
Ethernet network applications fields".
 |
10/100 Ethernet port interface,
RJ45 or TTL level (HE10 header connector) |
|
Compliant to the IEEE 802.11b
and IEEE 802.11g compatible, DSSS, (2.4 GHz wireless 11
Mbps Ethernet) recommendation, HIROSE UFL connector for external
antenna / cable |
|
200 m nominal range (line of sight), 60 m in other cases (with built-in antenna), up to 4 Km with a 20 dBi antenna |
|
auto-fallback system reduces speed to 5.5,
2 and 1 Mbps for greater range and/or better signal immunity |
|
4 independent 64/128 bits WEP keys |
|
No peripheral driver required,
configuration from standard internet web browser |
|
LEDs signalling for LAN &
WLAN network activity |
|
Compact printed circuit (L :76
x W :50 x H :18 mm) |
|
+3.3VDC or +5VDC power source,
3W maximum power consumption |
|
|
Mechanical characteristics and connectors Pin Out
|
Dimensions in mm
|
|
HE10 male connectors
(TTL level signals)
|
|
Pins (J3)
|
Dir.
|
Description
|
|
1
|
-
|
Unused
|
|
2
|
P
|
+3.3VDC (3W) (1)
|
|
3
|
O
|
LAN actity 3V3 LED (0
if active)
|
|
4
|
O
|
WLAN actity 3V3 LED
(0 if active)
|
|
5
|
O
|
Administration 3V3 LED
(1 if active)
|
|
6
|
I
|
Reset (active at 1)
|
|
7
|
P
|
+5VDC (3W) (1)
|
|
8
|
P
|
GND
|
| |
|
Pins (J6)
|
Dir.
|
Description
|
|
1
|
O
|
TxP (Ethernet, 3V3)
|
|
2
|
I
|
RxP (Ethernet, 3V3)
|
|
3
|
O
|
TxM (Ethernet, 3V3)
|
|
4
|
I
|
RxM (Ethernet, 3V3)
|
|
Note (1) :
Only one of the two power pins +3.3VDC (pin 2) or +5VDC
(pin 15) should be used simultaneously to power the
WL-BRIDGE-OEM.
Powering from the +3.3VC power pin apply power directly
to IC as the +5VDC go through a power regulator.
|
|
Application example
|
The WL-BRIDGE-OEM enables to connect two Ethernet networks
or two Ethernet equipments in the AD-HOC mode (direct radio
connection without infrastructure) or within a radio network
controlled by an Access Point as well.
The WL-BRIDGE-OEM can also be configured to work as a WiFi access Point.
WL-BRIDGE-OEM also supports the MODBUS/TCP protocol, thus
you can easily replace a network cable by the radio link to
connect any industrial equipment which rely on this protocol.
|
|
References to order:
| WL-BRIDGE-OEM-RJ |
Ethernet RJ45 10/100 Bridge
module & Access Point for wireless WiFi IEEE 802.11b, without antenna nor antenna
cable |
| WL-BRIDGE-OEM-TTL |
Ethernet (TTL) 10/100 Bridge
module & Access Point for wireless WiFi IEEE 802.11b, without antenna nor antenna
cable |
|
Add the -EVAL suffix pour the evaluation version
of OEM models, the samples are available
per one unit only and are delivered with antennna & antenna
cable (WL-KIT-ANT-1)
|
*** OEM products are not available through the distributor channel, please consult us directly ...
Accessories for the WL-BRIDGE-OEM family:
| WL-KIT-ANT-1 |
 |
RP-SMA 1 antenna kit with
15 cm cable for the WL-BRIDGE-OEM |
External antennas, RF cables, WiFi accessories:
 |
Click on the icon to the left to access the information request form |
 |
Click on the icon to the left to access the online documentations |
 |
Click to the PDF icon to download the technical data sheet |
|
|
